This machine adopts the series of the press, the mould adopts the special material to be made.
本机采用压力机系列，模具采用特殊材料制作。

How many mark do design for die and mould and fabrication attending Wuhan occupation Tec need.
读武汉职业技术学院的模具设计与制造需要多少分？

The assembled male mould is composed of a thermal expansion mould and a rigid metal structure.
其中组合阳模又由热膨胀软模和金属刚性支撑体组成。

The working principle and the working process of adsorption plastic mould of tank are introduced.
介绍箱体吸塑模的工作原理和工作过程。

Stir sticky rice powder and coco plasm.use them as stuffing.At last mould them into little apple.
将糯米粉跟椰浆, 拌匀蒸熟包馅, 做成小苹果的形状。

Participate in new mould quotation, formulate new mould manufacturing schedule and delivery date.
参与新模具的报价，制订新模具制造的进度表和交付日期。

The annealing process of centrifugal ductile cast iron pipe by the heated mould method is studied.
研究了热模法离心铸造球铁管的退火工艺。

Further movement of the moving mould plate actuates the stripper plate and the moulding is ejected.
动模板进一步的运动带动推板，使得塑件顶出。

Combine the seafood mixture and the Gruyere cheese together. Arrange the mixture in the tart mould.
将冷却的海鲜材料倒入碗中, 加瑞士细孔芝士拌匀, 放入挞中。

The design for the lens Block molded plastic mould design, design issues from the actual production.
本设计为物镜座的注塑模设计，设计课题来源于生产实际。

This article analyzes the forming technology of the spray tray, and design rational mould structure.
分析了淋盘成形工艺, 设计了合理的模具结构。

This machine mould replacement can system standard bricks, blind hole brick and other alien products.
本机更换模具可制标砖，盲孔砖及其它异型制品。

A Choice of Lubrication Mode for Running Mechanism of Ingot Mould Bogie of Anode Plate Casting Machine
阳极板浇铸机锭模小车运行机构润滑方式的选择

Contact with customer to understand what mould requirement and get mould drawing approval from customer.
与客户沟通模具要求及模具图纸的确认。

Down mold was adjusted the speed by Multistagebelt pulley, upper mould was used infinitely variable speeds.
下模多级皮带轮调速, 上模采用无级变速。

The affection of the carbon content on the average heat flux of mould of slab coninuous casting was discussed.
研究了碳含量对板坯结晶器平均热流的影响。

Preliminary Study On Purification And Properties of Antifungal Protein of Antibiotical Strain of Apple Mould Core
苹果霉心病生防菌株抗菌蛋白的提纯与部分性质初报

Study and Application on the Cast Material of Crack Resistance Gypsum Mould and Equal Wall Thickness of Cast Mould
抗裂石膏型铸造材料及铸型等壁厚研究与应用

Application of Standard Section Tunnel Lining Mould Bracing Arch for the Construction of Lining of Variable Section
隧洞标准段衬砌模板支撑拱架用于变截面段衬砌施工

The deficiencies in cold work tool and mould steels in China were analyzed compared with those in developed countries.
分析了国内外在冷作工模具钢方面的差距。

Received it already. Will send it to the mould cup supplier proceed the preproduction Samples for your fitting approval.
已收到, 我们将给模杯厂做产前办给您们批准。

The Influence of Mould Rotative Velocity and Coating Times on Quality of Coating Layer in Resin Bonded Centrifugal Mould.
铸型转速和布砂次数对离心树脂砂型覆砂层质量的影响

Actual Example Analysis about Wire Cutting Method of Motorcycle Start Electrical Machinery Rotor Silicon Steel Board Raised Hollow Mould
摩托车启动电机转子硅钢片凸凹模芯线切割加工分析

According to regulations, scientific and technological books need the type plate to be turned into paper mould after composition and proofreading.
按照规定，科技书一般实行三校付型。

For sake of the traditional calculation method appliance for the blanking die cutting edges dimensions, the potential value of mould cannot be embodied well.
传统方法计算的冲裁模刃口尺寸，模具的潜力不能充分发挥。