Redline of this engine is at 4200 RPM.
红线是这台发动机在4200转。

Frequency is related to crankshaft rpm.
频率是和曲轴的转速有关。

They develop 4. 5 horsepower at 9, 000 rpm.
当引擎转速为每分钟九千转时，具有4。5马力。

Increase power a bit, say to around 2000 rpm.
增加力量位，言对大约2000转每分钟。

Ignition timing must advance as rpm increases.
随著引擎转速得增加，点火正时必须提前。

Corner radivs against chipping in high RPM machining.
角设计可防止高速切削时崩刃。

The torque increases to incredible 860 Nm at 2000 rpm.
扭矩提高到了惊人得860牛米在2000转。

Maximum torque of 391 ftlb is achieved at just 2800 rpm.
最大扭矩391英尺磅是实现公正2800转。

This engine produces 440 Nm torque starting at 3000 rpm.
该引擎产生440牛米的扭矩从3000转。

Details We are looking for oscillating fan motor. Low rpm.
您现在还未登陆，请登陆后查看该采购客商的联系方式。

Study on RPM of Engine Crock Cover Air Way and Water Box Mould.
发动机缸盖气道及水腔模具快速成型技术研究

TurboLinux. Spec file Specification or RPM HOWTO or Maximum RPM.
本规范涵盖上述规范。

Digital display shows both actual and preset speeds in rpm or RCF.
数字显示屏显示实际转速和预设转速。

At what RPM should I run my general pump to achieve a desired flow.
问题我运行水泵，应该设置多少转每分钟，以达到希望的流量

With a meter which reads frequency, I am able to accurately tell rpm.
随着一米，其内容的频率，我能够准确地告诉每分钟转速。

The torque peak,which runs flat from 1500 to 5650 rpm,backs up this claim.
扭矩峰值，运行单位从1500年到5650转，支持了这种说法。

Measures the rpm of fans, motors, rollers etc., Without reflectors Part no.
测量风扇，电机，转轮等转速，无需反光贴。

Slower rpm s result in a more uniform melt by minimizing shear heat buildup.
较低的螺杆转速会由于最小的剪热而导致更均匀的熔化。

Slow RPM and light WOB are needed in drilling with a new bit at the beginning.
钻头使用初期要慢一点转, 钻压要低一点。

As engine rpm increases, there is less time for each step of the four stroke cycle.
当引擎转速增加, 四冲程循环每一步的时间变得越短。

When the motorcycle reaches closing RPM the throttle must be smoothly and fully closed.
当摩托车到达闭幕转速油门必须顺利，完全封闭。

Wired in parallel, reaches 12 volts at 240 rpm, with 12 amps charging current at 350 rpm.
有线平行, 达到12伏, 240转, 与12安培充电电流在350转。

In the low to mid RPM, the available spent exhaust energy spins up the smaller turbo only.
在低转速, 中期, 可用的能量旋转了排气小涡轮而已。

Never operate blades at rotational speeds greater than the maximum RPM listed on the blade.
从来没有工作在刀片比列出的最高转速转速大刀片。

This will keep your RPM much more consistent and accurate around idle where it really counts.
这将保持您得引擎转速准确维持在怠速。