A camshaft driven by a chain or belt turns in the same direction as the crankshaft.
凸轮轴被链或者带驱动，使其朝着曲轴相同的方向转动。

On some engines, a metal chain is used to connect the crankshaft and camshaft gears.
在一些发动机上，金属链被用来连结曲轴和凸轮轴齿轮。

Solution of Eigenvalue Problem of Crankshaft System by Lever Arm Coefficients Method
用力臂系数法求解发动机曲轴系统特征值问题

Comparison between Steel Shots and Glass Shots in Shot Peening of Crankshaft Fillets
用铸钢丸和玻璃丸对曲轴圆角喷丸强化的对比分析

Casting defects, especially porosity, will reduce fatigue strength of the crankshaft.
铸造缺陷, 尤其是铸造缩松, 降低了曲轴的疲劳强度。

Automatic Test Machine of Distance Between Crankshaft Neck and Top Surface of Cylinder
曲轴连杆颈到缸体顶面距离自动检测机

A belt driven by the crankshaft that drives a fan that pulls air through the radiator.
受机轴控制驱动风扇使风扇在散热器里拖拉空气的带子。

a belt driven by the crankshaft that drives a fan that pulls air through the radiator.
驱动风扇使风扇在散热器里拖拉空气的带子。

Study on Granding Double Round Corner and Rolling Twill Lines in Crankshaft Processing
曲轴磨双圆角及滚斜纹工艺的研究

If the limit of wear is equalled or exceeded, replace the crankshaft and bearing shells.
如果等于或超过磨损极限，请更换曲轴和轴瓦。

The nationalization of engine crankshaft blank for Jetta, Bora and Golf car was realized.
实现了捷达、来和高尔夫轿车发动机曲轴毛坯的国产化。

The irrational distribution of crankshaft counterbalance weight causes greater vibration.
曲轴平衡块质量分布不合理，会引起发动机振动大。

The connecting rod is used to transmit the pressure applied on the piston to the crankshaft.
连杆的作用是将从活塞传来的力传给曲轴。

A pilot bushing fits into the back of the crankshaft and holds the transmission input shaft.
飞行员衬套装入曲轴得背部和变速器输入轴持有。

Experimental Study on Deep Rolling of Undercut Fillet Radii for Nodular Cast Iron Crankshaft
球铁曲轴圆角沉割滚压试验研究

Industry Steering rod Knuckle Transmission shaft Connecting Rod Assembly Crankshaft, camshaft.
所属行业转向拉杆转向节传动轴连杆总成曲轴，凸轮轴

Study on Mechanism of Bubbling in Gas Nitrocarburizing of Nodular Graphite Cast Iron Crankshaft
球墨铸铁曲轴气体氮碳共渗鼓泡机理探讨

Crankshaft surface rolling is one of the most important approaches to expand the crankshaft life.
曲轴圆角滚压强化技术是提高曲轴寿命的最主要途径之一。

A crank arm is the offset portion of a crankshaft to which connecting rod and position are attached.
曲柄臂是曲轴连接臂，其中安装连杠和活塞。

Remove the top half brasses of all main bearings and measure crankshaft worn down with bridge gauge.
拆下各主轴承上瓦，用桥规测量曲轴的磨耗。

The motion of the rotor can be balanced completely with rotating counterweights attached to the crankshaft.
使用连接在曲轴上的转动平衡块，转子的运动就能完全平衡。

As the piston strokes in its bore, the crankshaft rotates, pressurizing the opposite bore reverses rotation.
正如在其孔活塞杆，曲轴旋转，加压相反的孔反转旋转。

Carefully remove smaller edges or burrs on the chamfer of the crankshaft flange with an oilstone if necessary.
如有必要, 请用油石仔细去除曲轴法兰倒棱上的小边或毛刺。

Considering the variable inertia of the reciprocating parts, free torsional vibration characteristics of crankshaft are studied.
研究往复运动件变惯量下的曲轴系自由扭振特性。

This paper described the foundry technology of horizontal pouring and solidifying to produce large hollow ductile iron crankshaft cast in sand coated iron mould.
介绍了铁模覆砂铸造大型空心球铁曲轴的工艺。