Analysis and Calculation of Prism Height on Side Face of Hypocycloid Gear Machined by Gear Shaper.
摆线齿轮齿侧棱线高度的分析计算

In addition, when roller gear when no meshing clearance between generates this kind of gear poles.
另外, 当不朱辊齿轮之间无啮合间隙时也会爆发这栽齿轮杠。

The absorber system of landing gear has a decisive influence on the taxiing performance of airplane.
起落架缓冲系统对飞机的滑行性能有着决定性的影响。

Guarantee the Manufacturing Accuracy of the Conical Curved Teeth Gear by Milling Instead of Grinding
以铣代磨保证弧齿锥齿轮加工精度

Applying the Relation of Gear Size to Calculating the Geometric Size of Gear with Displacement Angle
利用轮齿尺寸关系计算角变位齿轮几何尺寸

There are lifting ears at the lower casing of the gear reducer used for lifting the whole gear reducer.
减速机下箱体上设置有专门用于吊装整台减速机的吊耳。

Gear racks are arranged at the side face of the transverse arm part and are meshed with the driving gear.
所述横臂部件侧面装有齿条，齿条与驱动齿轮啮合。

When a powered gear goes through a full rotation, it pulls the chain by the number of teeth on that gear.
当加电的轮旋转一周时，它根据轮上的数来拉动链条。

The efficiency of the experimental gear for the bigeye tuna was greater than that of the traditional gear.
试验钓具大眼金枪鱼的捕捞效率高于传统钓具。

Study on the new inner planar moving spur gear typed epicyclic gear transmission with few teeth difference
外齿轮内平动式新型少齿差行星传动的研究

The Influence of the Teeth Number of Driving Gear on the Flow Characteristics of Compound External Gear Pump
中心轮齿数对复合式外齿轮泵流量脉动的影响分析

Analysis of Engaging Force of Gears Used in Transmission Mechanism Composed of Circular Arc Gear and Pin Gear
圆弧少齿差传动齿轮啮合作用力分析

bevel gear Either of a pair of gears with teeth surfaces cut so that they can connect unparallel gear shafts.
斜齿轮用以连接不平行齿轮轴齿轮的任一对齿面切削。

In the production of gear shaping machine, the phenomenon of gear mark is a problem that cannot be neglected.
在插齿机生产中, 插齿接刀痕现象是一个不容忽视的问题。

The steering gear shall be controlled from the wheelhouse or emergency control by hand near the steering gear.
舵机应能在驾驶室操纵和机旁应急手动操纵。

The equipments maintenance plan about the imported gear grinding machines and gear shaving machines and so on.
进口磨齿机，剃齿机和剃刀磨等设备维护计划。

Manual gear changes are made either with shift paddles or buttons on the steering wheel or with the gear lever.
手动换挡可用方向盘上的拨杆和按钮，也可用换挡杆。

When shaft and gear is in a normal state, abnormal impact phenomenon does not occur during the vibration process.
当轴和齿轮正常工作时, 振动过程不产生异常冲击。

Measuring Tool for Special Use to Survey the Degree of Coaxial for the Joint Circular of Inner Gear and Outword Gear
测量内齿节圆与外圆同轴度的专用量具

The effect of Gear Structural Parameters and Errors on the Main Gear Transmission Vibrations of a Marine Propulsion Plant
齿轮结构参数和误差对某动力装置主齿轮传动振动的影响

ANALYSIS ON LOAD CHARACTERISTICS OF MESHING BETWEEN IMPROVED CYCLOID GEAR AND PIN TEETH OF CYCLOID PIN GEAR PLANETARY REDUCER
修正齿形摆线轮与针轮啮合时受力特性的研究

A comparison was made on force bearing conditions of the cycloidal gear with the same typed two pieced gear cycloidal reducer.
并与同种机型两片轮摆线减速机的摆线轮受力进行比较。

An Exploration into the Matching Problem of the Gear Number, Spiral Cape of Inclined Gear, and Modification Coefficient of Gearbox
变速器的齿轮齿数及螺旋角变位系数的匹配

And it introduced the relation gear tooth concave hole parameter and hob used of tooth cut and rub tooth surplus and match gear geometry parameter.
介绍了齿轮齿根凹圆坑参数与所用滚刀的关系。

Two measures, one is the method of counteracting strain, another is the method of fixing two sets of2322 bearings in bearing box on the end of gear, are taken in order to improve the stress status of gear in blower on high load.
采取两种措施改善高负荷下风机齿轮得受力情况。